FRS Spec D Specific HID Kit
$210.00 – $240.00Price range: $210.00 through $240.00
A direct fit HID kit for FRS Spec D Headlight, with no modifications to housing necessary.
The stock bulbs that come with the headlights are H1….but need adapters to be used in a D2S bulb holder… strange. Let’s just cut out the middle man and put the bulb in there that was intended to be there. Enter the FRS Spec D Specific HID Kit.
Click pictures to enlarge and see captions with instructions, or click on the Instructions tab below.
Please allow 2-3 days shipping time if including Morimoto products.
For more pictures & videos, visit our Instagram: www.instagram.com/gtaretrofits
FRS Spec D Specific HID Kit
No frills or fancy packaging, just honest performance and reliability for your money, this HID kit is near plug and play and will greatly improve the performance of your Spec D Headlights
STANDARDS: The Hylux 2A88 EU-Spec Canbus HID ballast is what the FRS Spec D Specific HID Kit was built around, set to produce an industry-standard 35w of power which typically provides around 3200 lumens on a quality 4300K Bulb. They will accept a 9-16V range for input and will power all HID bulbs with industry-standard AMP connectors, perfect for this kit.
RELAY WIRE HARNESS: As one of the most important parts in any HID lighting upgrade; don’t skimp out when it comes to your wiring. It doesn’t matter how good your ballasts are, or how good your bulbs are if your harness is a piece of crap (or fuses rated too low) when it gives out your headlights are gonzo. These harnesses are the best on the market and easily worth their price. No matter which one is right for your application, the harness features triple-sealed relay packs, stranded copper wiring, over-molded fittings, and plug-n-play functionality. This will ensure everything properly (and permanently) works with your vehicle’s original in-cabin controls.
Includes
-
- Female Connectors for interior wiring
- Heat Shrink
- D2S to AMP DIY Adapters
- H1 to 9006 Female Plug
- NHK D2S Bulbs 5500k
- Hylux 35W Ballast or Morimoto XB
| Weight | 1.4 kg |
|---|---|
| Dimensions | 31 × 26 × 11 cm |
| Bulb | NHK 5500k |
| Ballast | Hylux 2088 (Recommended), Morimoto XB 35W, Morimoto XB 55W |
| Relay | None, NHK VIP Dual Relay Harness, Morimoto HD Low Beam Harness |
Warranty
1 Year warranty:
- Bulbs
- Igniters
- Relay (Optional)
2 Year warranty:
- Morimoto Ballast
3 Year warranty:
- Hylux Ballast
Installation
Quick Steps:
- Snip off OEM bulb connectors
- Crimp on supplied female spade connectors
- Feed D2S-to-Amp adapters & H1-to-9006 adapter through bottom holes in the cap. Assemble the D2S-to-amp plugs. Making sure to insert the wires as far as possible, it is recommended to tug them through with small needle-nose pliers. Once you’ve insert red locking pieces, push down on the male (white wire one) locking piece to ensure it’s completely recessed and locked into place. Gently tug on wires to confirm proper seating.
- Remove halogen bulb & all metal adapters
- Insert D2S Bulb
- Identify Spec D Ground & Power Wires (Ground has a black line, Power is solid blue or Blue with Red)
- Insert H1-to-9006 spade plugs into corresponding female spade connectors & tape up all connections to prevent shorts
- Twist on D2S-to-amp adapter. Recommended at 90-degree angle as shown
- Replace cap & seal holes with a small amount of silicone.
1 review for FRS Spec D Specific HID Kit
Only logged in customers who have purchased this product may leave a review.
Related Products
$180.00 – $295.00Price range: $180.00 through $295.00
Select options This product has multiple variants. The options may be chosen on the product page
$160.00 – $205.00Price range: $160.00 through $205.00
Select options This product has multiple variants. The options may be chosen on the product page
GTA Retrofits$175.00 – $306.00Price range: $175.00 through $306.00
Select options This product has multiple variants. The options may be chosen on the product page
Daymond B (verified owner) –
I got the vip harness just incase, but it is not necessary to set up just the low beams, and to do the high beams as well requires other parts. Over all pretty straight forward and easy.